The All Balls Racing AB6-PO-8-381 is a heavy-duty 6-Ball rear CV axle for 60-inch Polaris models — the General 1000 and General 4 1000 (2016-2019), RZR 900 S and RZR 900 Trail S (2015-2023), RZR 4 900 (2015-2018), RZR 1000 60 Inch and RZR 1000 Trail S (2016-2023), and RZR S4 1000 (2019-2020) — replacing Polaris OEM rear halfshafts 1333081 and 1333947. It arrives as one complete, pre-assembled axle with the installation hardware included, so a broken or clicking rear axle can go from diagnosis to trail-ready in a single service.
The shaft is heavy-duty chromoly steel for increased torsional strength, and each CV joint is packed with high-performance molybdenum grease to reduce heat and friction under load. Heavy-duty neoprene boots seal grease in and keep water, sand, and grit out, while a laminate coating on the shaft resists rust and corrosion through water crossings and winter storage.
What's Included
- One (1) complete, pre-assembled All Balls 6-Ball rear CV axle
- Washer, axle nut, and cotter key
Sold as a single axle covering one position.
Specifications
-
Brand: All Balls Racing
-
Part Number: AB6-PO-8-381
-
Product Line: 6-Ball Heavy Duty Axle
-
Position: Rear (our fitment data lists the rear right position)
-
Shaft: Heavy-duty chromoly steel
-
Boots: Heavy-duty neoprene
-
Grease: High-performance molybdenum
-
Coating: Laminate anti-corrosion shaft coating
-
Replaces Polaris OEM: 1333081 and its superseding number 1333947
-
Warranty note: Warranty void if disassembled; not designed or intended for modified vehicles
Fitment
The All Balls AB6-PO-8-381 fits the rear axle position on the Polaris General 1000 EPS from 2016 to 2018, including the 2018 Deluxe, Hunter Edition, Premium, and Ride Command trims and the 2019 Limited Edition, plus the General 4 1000 EPS from 2017 to 2018. It fits the rear of the Polaris RZR 900 S 60 Inch (2015-2020), RZR 900 Trail S Sport (2021-2023), and RZR 4 900 (2015-2018). It fits the rear of the Polaris RZR 1000 60 Inch (2016-2021), RZR 1000 Trail S (2021-2023 Premium, Ultimate, and Trail S trims), and RZR S4 1000 (2019-2020). These are the 60-inch General and RZR S platforms — the same machines that use Polaris rear halfshaft 1333081/1333947. Our fitment data lists the rear right position; before ordering for the left side, verify your OEM part number against 1333081 or 1333947.
Does not fit Polaris RZR XP 900, RZR XP 1000, RZR XP 4 1000, or RZR XP Turbo models — the XP chassis uses different rear axles. Does not fit front positions. This axle is a direct OEM-style replacement for stock machines at stock ride height; All Balls axles are not designed or intended for lifted or otherwise modified vehicles.
Does AB6-PO-8-381 fit the rear left or rear right?
Our fitment data lists the rear right position. The Polaris OEM halfshaft it replaces (1333081/1333947) is the rear axle for these General and RZR S models; if you are replacing the left side, verify your machine's OEM part number before ordering.
What Polaris OEM part numbers does this axle replace?
It replaces Polaris rear halfshaft 1333081 and its superseding part number 1333947.
Will this axle fit a Polaris RZR XP 1000?
No. RZR XP 900, XP 1000, XP 4 1000, and XP Turbo models use different rear axles. This axle covers the 60-inch General 1000 and RZR S / RZR Trail S platforms listed in the fitment chart.
What hardware comes with the axle?
Each axle includes the washer, axle nut, and cotter key needed for installation, and ships fully assembled with both CV joints installed.
SaleFree Shipping
