{"product_id":"kn-engineering-elevated-intake-snorkel-63-8003-2024-toyota-tacoma","title":"K\u0026N Engineering 63-8003 Snorkel Intake Kit for 2024-26 Toyota Tacoma","description":"\u003cp\u003eThe K\u0026amp;N Engineering 63-8003 Elevated Intake Kit is a fender-mounted snorkel for the 2024-2026 Toyota Tacoma with the L4-2.4L turbo engine and the 2026 Toyota 4Runner, and it is a snorkel assembly only: K\u0026amp;N Engineering states it must be used with the K\u0026amp;N Engineering 63-9043 intake system, which is sold separately.\u003c\/p\u003e\u003cp\u003eOn the fourth-generation Tacoma the factory air pickup sits low in the passenger-side inner fender - exactly where dust hangs on a washboard road. The 63-8003 carries that pickup up the A-pillar to roof height instead. It is a body-modification kit, not a bolt-on: the instruction sheet has you open four 3\/8 in and three 1\/2 in mounting holes and cut a 4 in pass-through with a hole saw in the passenger-side fender, then deburr and paint the bare edges. K\u0026amp;N Engineering recommends a professional installer if that work is outside your comfort zone.\u003c\/p\u003e\u003ch3\u003eKey Benefits\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eRelocates the intake pickup out of the inner fender and up to the top of the passenger-side A-pillar.\u003c\/li\u003e\n\u003cli\u003eCapped by a K\u0026amp;N Engineering snorkel top with an integrated grill, clamped on with a #72 hose clamp.\u003c\/li\u003e\n\u003cli\u003eBraced at two points - seven M6 studs through the fender plus a dedicated A-pillar mount bracket on double-sided tape.\u003c\/li\u003e\n\u003cli\u003eRubber sealing washers sit behind the large fender washers at every stud, so the drilled fender is sealed at the fastener line.\u003c\/li\u003e\n\u003cli\u003eShips with a factory fresh-air block-off and a K\u0026amp;N airbox lid block-off, so in extreme conditions all intake air can be forced through the snorkel.\u003c\/li\u003e\n\u003cli\u003eComplete hardware pack - studs, nylock nuts, fender washers, grommets, screw grommets and two hose clamps are all in the box.\u003c\/li\u003e\n\u003cli\u003eEngineered as a matched pair with the K\u0026amp;N Engineering 63-9043 intake; K\u0026amp;N Engineering states the snorkel will not bolt to the stock system or to any other manufacturer's intake.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhat's Included\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eSnorkel body, inner tube and K\u0026amp;N Engineering snorkel top with grill\u003c\/li\u003e\n\u003cli\u003eSnorkel coupler, 9\/16 in ID grommet and two inner screw grommets\u003c\/li\u003e\n\u003cli\u003eFresh-air block-off plate and black rubber lid block-off\u003c\/li\u003e\n\u003cli\u003eSeven M6-1.0 x 40 mm studs and seven M6 nylock nuts\u003c\/li\u003e\n\u003cli\u003eThree 1 in fender washers, four 1\/4 in ID washers and four rubber sealing washers\u003c\/li\u003e\n\u003cli\u003eA-pillar mount bracket with double-sided mounting tape\u003c\/li\u003e\n\u003cli\u003eTwo M6-1 x 20 mm hex bolts, one #60 and one #72 hose clamp\u003c\/li\u003e\n\u003cli\u003eInstruction sheet with two full-size drilling templates\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitment\u003c\/h3\u003e\u003cp\u003eK\u0026amp;N Engineering lists the 63-8003 for the 2024-2026 Toyota Tacoma with the L4-2.4L turbo engine and for the 2026 Toyota 4Runner. Because the kit is a snorkel only, it can be run solely in combination with the K\u0026amp;N Engineering 63-9043 intake system, and K\u0026amp;N Engineering states that 63-9043 will not fit the 2024-2026 Tacoma TRD Pro or the 2025-2026 4Runner TRD Pro - so the snorkel does not fit a TRD Pro either. It does not fit a vehicle with a body lift, and it does not bolt to the factory airbox or to any other brand's intake. K\u0026amp;N Engineering also states that the kit does not increase the manufacturer's suggested water fording limit for the vehicle,. K\u0026amp;N Engineering names only the 2.4L turbo engine and the TRD Pro exclusion on this application; it publishes no i-FORCE MAX hybrid, cab, bed or transmission restriction. Do not confuse the two part numbers: 63-9043 is the intake system itself - airbox, tube, dry filter and MAF adapter - and is the required companion, while 63-8003 adds only the elevated snorkel stack that feeds it. No CARB Executive Order was found for 63-8003, so this part is not legal for sale or use in California or other states that have adopted California emission standards.\u003c\/p\u003e","brand":"K\u0026N Engineering","offers":[{"title":"Default Title","offer_id":53462371598633,"sku":"63-8003","price":589.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1584\/9683\/files\/00_209e3f9c-6cca-4e59-ae8d-5447197d426d.jpg?v=1788192743","url":"https:\/\/www.dirtmasters.com\/products\/kn-engineering-elevated-intake-snorkel-63-8003-2024-toyota-tacoma","provider":"Dirt Masters","version":"1.0","type":"link"}